Kia Cee'd: Airbag Module / Airbag Module Disposal Description and operation
Deployment tool 0957A-34100A
Before scrapping any airbags or side airbags (including those in a whole vehicle
to be scrapped), the airbags or side airbags must be deployed. If the vehicle
is still within the warranty period, before deploying the airbags or side airbags,
the Technical Manager must give approval and/or special instruction. Only after
the airbags or side airbags have been deployed (as the result of vehicle collision,
for example), can they be scrapped. If the airbags or side airbags appear intact
(not deployed), treat them with extreme caution. Follow this procedure.
Deploying airbags in the vehicle
If an SRS equipped vehicle is to be entirely scrapped, its airbags or side airbags
should be deployed while still in the vehicle. The airbags or side airbags should
not be considered as salvageable parts and should never be installed in another
vehicle.
| 1. |
Turn the ignition switch OFF, and disconnect the battery negative cable
and wait at least three minutes.
|
| 2. |
Confirm that each airbag or side airbag is securely mounted.
|
| 3. |
Confirm that the special tool is functioning properly by following the
check procedure.
| (1) |
Driver’s Airbag :
| –
|
Remove the driver’s airbag and install the SST (0957A-3S100).
|
| –
|
Install the driver’s airbag on the steering wheel.
|
|
| (2) |
Front Passenger’s Airbag :
| –
|
Remove the glove box housing, and then disconnect the
connector between the front passenger’s airbag and SRS
main harness.
|
| –
|
Install the SST(0957A-3S100).
|
|
| (3) |
Side Airbag :
| –
|
Disconnect the 2P connector between the side airbag
and wire harness.
|
| –
|
Install the SST (0957A-3F100).
|
|
| (4) |
Curtain Airbag :
| –
|
Disconnect the 2P connector between the curtain airbag
and wire harness.
|
| –
|
Install the SST(0957A-3S100).
|
|
| (5) |
Seat Belt Pretensioner :
| –
|
Disconnect the 2P connector from the seat belt pretensioner.
|
| –
|
Install the SST (0957A-3S100).
|
|
|
| 4. |
Place the deployment tool at least thirty feet (10meters) away from
the airbag.
|
| 5. |
Connect a 12 volt battery to the tool.
|
| 6. |
Push the tool’s deployment switch. The airbag should deploy (deployment
is both highly audible and visible: a loud noise and rapid inflation
of the bag, followed by slow deflation)
|
| 7. |
Dispose of the complete airbag. No parts can be reused. Place it in
a sturdy plastic bag and seal it securely.
|
Deploying the airbag out of the vehicle
If an intact airbag has been removed from a scrapped vehicle, or has been found
defective or damage during transit, storage or service, it should be deployed
as follows:
| 1. |
Confirm that the special tool is functioning properly by following the
check procedure on this page.
|
| 2. |
Position the airbag facing up and EFD (Emergency Fastening Device) and
Active Hood Actuator must be placed in piled up, at least, 5 tires,
outdoors on flat ground at least thirty feet (10meters) from any obstacles
or people.
|
| 3. |
Connect a 12 volt battery to the tool.
|
| 4. |
Push the tool’s deployment switch. The airbag should deploy (deployment
is both highly audible and visible: a loud noise and rapid inflation
of the bag, followed by slow deflation)
|
| 5. |
Dispose of the complete airbag. No parts can be reused. Place it in
a sturdy plastic bag and seal it securely.
|
| – |
When EFD and Active Hood Actuator are deployed, broken parts
are exploded and scattered.
|
| – |
EFD and Active Hood Actuator must be placed in the piled up
5 tires to avoid exploded broken parts.
|
| – |
Technicians should wear an eye protector and extremely be cautions
of exploded broken parts.
|
|
Disposal of damaged airbag
| 1. |
If installed in a vehicle, follow the removal procedure of driver’s
airbag front passenger’s and side airbag.
|
| 2. |
In all cases, make a short circuit by twisting together the two airbag
inflator wires.
|
| 3. |
Package the airbag in exactly the same packing that the new replacement
part come in.
|
Removal
1.
Disconnect the battery negative cable and wait for at least thirty seconds
before beginning work.
2.
Remove the roof trim a ...
Other information:
Kia Cee'd JD Owners Manual: Connecting an External Device
External audio players (Camcorders,
car VCR, etc.) can be played through
a dedicated cable.
✽ NOTICE
If an external device connector is
connected with the AUX terminal,
then AUX mode will automatically
operate. Once the connector is disconnected,
the previous mode will
be r ...
Kia Cee'd JD Service Manual: Special service tools
Special Service Tools
Tool(Number and Name)
Illustration
Use
09495-3K000
Band installer
Installation of ear type boot band
09495-33000
Puller
...
Curtain Airbag (CAB) Module Repair procedures