Kia Ceed Manuals Ceed Car Manuals
Technical Info

Kia Cee'd: Driveshaft Assembly / Front Driveshaft Repair procedures

Kia Cee'd JD Service Manual / Driveshaft and axle / Driveshaft Assembly / Front Driveshaft Repair procedures

Replacement
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from front hub .
Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

  
Be careful not to damage to the hub bolts when removing the rear wheel and tire (A).
3.
Remove the driveshaft coking nut (A).
Tightening torque:
274.4 ~ 294.3 N.m (28.0 ~ 30.0 kgf.m, 202.4 ~ 217.0 lb-ft)

  
The driveshaft lock nut should be replaced with new ones.
After installation driveshaft lock nut, stake the lock nut using a chisel and hammer as shown in the illustration below.

4.
Remove the tie rod end ball joint (C) from the knuckle by using the SST (09568-34000).
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).
(3)
Use the SST (09568-34000).
Tightening torque:
23.5 ~ 33.3N.m (2.4 ~ 3.4kgf.m, 19.4 ~ 24.6lb-ft)

  
When using SST, be sure not to damage the dust cover of lower arm ball joint.
Keep SST tied to the car because there is a risk of injury by dropping the SST during removing the lower arm ball joint.
The peripheral parts may be damaged when removing the lower arm ball joint with a general tool such as lever, so be sure to use SST.
5.
Remove the lower arm (A) from the knuckle.
Tightening torque:
98.0 ~ 117.6 N.m(10.0 ~ 12.0 kgf.m, 72.3 ~ 86.7 lb-ft)

6.
Using a plastic hammer, disconnect driveshaft (A) from the axle hub (B).

7.
Loosen the inner shaft mounting bolt (A). (T-GDI Engine only)
Tightening torque:
49.0 ~ 63.7N.m (5.0 ~ 6.5kgf.m, 36.2 ~ 47.0lb-ft)

8.
Insert a pry bar (A) between the transaxle case and joint case, and separate the drive shaft (B) from the transaxle case.

9.
Install in the reverse order of removal.
Front Driveshaft Components and components location
Component   1. Driveshaft (LH) 2. Circlip 3. Driveshaft (RH) ...
TJ Joint Components and components location
Components [LH]   1. BJ assembly 2. BJ circlip 3. BJ boot band 4. BJ boot 5. Shaft 6. TJ boot band 7. TJ boot 8. Sp ...
Other information:

Kia Cee'd JD Service Manual: Specifications
Specification Ignition System Ignition Coil   Item Specification Primary Coil Resistance (Ω) 0.75 ± 15% [20°C (68°F)] Secondary Coil Resistance (kΩ) 5.9 [20°C (68°F)] ...

Kia Cee'd JD Owners Manual: Emergency tailgate safety release
❈ The actual luggage room in the vehicle may differ from the illustration. Your vehicle is equipped with the emergency tailgate safety release lever located on the bottom of the tailgate. When someone is inadvertently locked in the luggage compartment. The tailgate can be opened by ...

Copyright © www.kiamanual.com 2020-2024 | Privacy Policy | Kia Car Parts