Kia Cee'd: Windshield Wiper/Washer / Front Wiper Motor Repair procedures

Kia Cee'd JD Service Manual / Body Electrical System / Windshield Wiper/Washer / Front Wiper Motor Repair procedures

Removal

Remove the cap (B) and remove the nuts, then remove the wiper arm (A).

Tightening torque :

22.6 ~ 26.5 N.m(2.3 ~ 2.7 kgf.m, 16.6 ~ 19.5 lb-ft)

2.	If necessary, release the wiper blade fixing clip by pulling up and remove the wiper blade from the inside radius of wiper arm.

3.	Remove the weather strip and the cowl top cover (A) after removing 4 rivets.

4.	Disconnect the washer hose (B) connected to cowl top cover.

5.	Remove the windshield wiper motor and linkage assembly (A) after removing 2 bolts.

6.	Disconnect the wiper motor connector (A) from the wiper motor & linkage assembly.

7.	Hold the wiper motor crank arm and remove the upper linkage (A) from the wiper motor crank arm.

8.	Remove the lower linkage (A) from the wiper motor crank arm.

Hold the arm using the plyer, remove the crank arm (A) after loosening the mounting nut.

Before removing the wiper motor and linkage assembly, make sure that the linkage is stopped at auto stop position.

To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.

Be careful not to bend the linkage.

10.	Remove the wiper motor (A) with 3 bolts.

Installation

1.	Install the wiper motor.

Install the crank arm.

To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly.

Install the lower and upper linkage to the wiper motor crank arm.

To install the wiper motor crank arm, make sure that the linkage is aligned with the crank arm in straight line and set the angle of each linkages exactly.

Be careful not to bend the linkage.

Install the wiper motor and linkage assembly and then connect the wiper motor connector.

Tightening torque:

6.9 ~ 10.8Nm (0.7 ~ 1.1, kgf.m, 5.0 ~ 7.9 lb-ft)

5.	Install the cowl top cover.

Install the windshield wiper arm and blade.

Tightening torque:

22.6 ~ 26.5 Nm (2.3 ~ 2.7 kgf.m, 16.6 ~ 19.5 lb-ft)

–	The windshield wiper motor must be cycled to make sure that it is in the auto stop position. If necessary, adjust the wiper arm and blade.

7.	Install the wiper arm and blade to the auto stop position. A : Auto stop position (Blade)

Inspection

Speed Operation Check

Remove the connector (A) from the wiper motor.

No.	Description	No.	Description
1	GND	4	Low
2	Parking	5	High
3	Battery	6	-

2.	Attach the positive (+) lead from the battery to terminal 3 and the negative (-) lead to terminal 1.

Check that the motor operates at low or high speed as below table.

Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes. If the blades are not wiping properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.

Front Wiper Motor Components and components location

Component Location 1. Cap 2. Nut 3. Wiper arm & blade 4. Rivet 5. Cowl top cover 6. Bolt 7. Wiper motor & linkage assembly ...

Front Washer Motor Repair procedures

Inspection Front and Rear Washer Motor 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water. ...

Other information:

Kia Cee'd JD Service Manual: Power Mosfet (DATC) Repair procedures
Inspection 1. Turn the ignition switch ON. 2. Manually operate the control switch and measure the voltage of the blower motor. 3. Select the control switch to raise the voltage until high speed. ...

Kia Cee'd JD Owners Manual: SRS Care
The SRS is virtually maintenance-free and so there are no parts you can safely service by yourself. If the SRS air bag warning light does not illuminate, or continuously remains on, we recommend that the system be inspected by an authorized Kia dealer. WARNING Modification to SRS co ...