Kia Cee'd: Parking Brake System / Parking Brake Cable Repair procedures

Kia Cee'd JD Service Manual / Brake System / Parking Brake System / Parking Brake Cable Repair procedures

Removal

The parking brake cables must not be bent or distorted. This will lead to stiff operation and premature failure.

1.	Remove the floor console assembly. (Refer to Body - "Floor console")

2.	Disconnect the connector (A) of parking brake switch.

Loosen the adjusting nut (A) and the parking brake cables (B).

Parking brake lever in the car must be in fully loosened position.

4.	Raise the vehicle, and make sure it is securely supported.

5.	Remove the rear tire and wheel.

6.	Remove the parking brake cable (A), after removing the clip (B).

7.	Loosen the parking brake cable bracket bolts and remove the parking brake cable (A).

Installation

Install the parking brake cable (A).

Tightening torque :

Bolts : 8.8 ~ 14.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

Nuts : 6.9 ~ 10.7 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

2.	Install the parking brake cable (A), and then install the clip (B).

3.	Install the rear tire and wheel.

4.	Install the parking brake cable (A).

Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.

Specified grease:

Multi purpose grease SAE J310, NLGI No.2

Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke:

6 ~ 8 clicks (Pull the lever with 196N (20 kgf, 44 lbf))

After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

7.	Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.

8.	Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.

Reconnect the connector (A) of parking brake switch.

Inspect the continuity of parking brake switch.

When the brake lever is pulled: continuity

When the brake lever is released: no continuity

10.	Install the floor console. (Refer to Body - "Floor console")

Adjustment

Parking Brake Lever Stroke Adjustment

1.	Remove the floor console. (Refer to Body - "Floor console")

2.	Apply the brake pedal 20 times with the force of 10kgf after bleeding. Then, for the cable to settle in, apply the parking brake full stroke more than 3 times.

Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke :

6 ~ 8 clicks (Pull the lever with 196N (20 kgf, 44 lbf))

After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

4.	Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.

5.	Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.

6.	Install the floor console. (Refer to Body - "Floor console")

Rear Brake Caliper Gap

Re-setting of the parking brake is necessary after overhauling the caliper body, or if the brake calipers, housing, parking brake cable or brake discs have been changed.

1.	Remove the floor console to reach the adjusting nut.

2.	Loosen the parking brake cable until both operating levers rest in fully off position.

3.	Bring the brake pads in their operating position by pressing the brake pedal down several times until there is resistance.

Tension the parking brake cable by tightening the adjusting nut, until the operating levers on both calipers lift from the stop, up to a distance of (A) and (D) between operating lever (B) and stopper (C).

Distance (A+D): Max. 3 mm (0.12 in)

5.	Refit the floor console.

6.	Parking brake lever in the car must be in fully loosened position.

7.	If the handbrake cables where changed, actuate the parking brake a few times with maximum force to stretch the parking brake cables, and then control adjusting as above.

8.	Check the wheels of their free operation.

9.	Test drive.

Parking Brake Lever Repair procedures

Removal The parking brake cables must not be bent or distorted. This will lead to stiff operation and prema ...

Electronic Parking Brake (EPB) Components and components location

Components 1. EPB Unit 2. EPB Switch 3. Brake Caliper 4. EPB Warning Lamp ...

Other information:

Kia Cee'd JD Owners Manual: Starting the engine
WARNING Always wear appropriate shoes when operating your vehicle. Unsuitable shoes (high heels, ski boots,etc.) may interfere with your ability to use the brake and accelerator pedal, and clutch (if equipped). ✽ NOTICE - Kick down mechanism If your vehicle is equipped with a kick d ...

Kia Cee'd JD Service Manual: Accelerator Position Sensor (APS) Specifications
Specification Accelerator Position Output Voltage (V) [Vref=5V] APS1 APS2 C.T 0.7 ~ 0.8 0.29 ~ 0.46 W.O.T 3.85 ~ 4.35 1.93 ~ 2.18 ...