Kia Cee'd: Driveshaft Assembly / TJ Joint Repair procedures

Kia Cee'd JD Service Manual / Driveshaft and axle / Driveshaft Assembly / TJ Joint Repair procedures

Replacement

•	Special grease must be applied to the driveshaft joint. Do not substitute with another type of grease.

•	The boot band should be replaced with a new one.

1.	Remove the Front Driveshaft. (Refer to Driveshaft Assembly - “Front Driveshaft”)

2.	Remove the housing circlip (B) from the driveshaft spline (A).

3.	Remove both boot bands from the TJ housing.

Remove the TJ housing (A).

•	Make alignment marks on spider roller assembly (A), joint case (B), and shaft spline (C) to aid reassembly.

5.	Remove the retainer ring (A) from the shaft.

6.	Remove the spider assembly (B) from the driveshaft (A) using the special tool (09495-33000).

7.	Clean the spider assembly.

Remove the TJ boot (A).

•	For reusing the boot (A), wrap tape (B) around the driveshaft splines (C) to protect the boot (A).

Inspection

1.	Check the spider assembly for roller rotation, wear or corrosion.

2.	Check the groove inside the joint case for wear or corrosion

3.	Check the TJ boots for damage and deterioration.

Installation

1.	Wrap tape around the driveshaft spline(TJ) to prevent damage to the boot.

2.	Using the alignment marks (D) made during disassembly as a guide, install the spider assembly (A) and retainer ring (B) on the driveshaft splines (C).

3.	Add specified grease to the joint boot as much as it was wiped away at inspection.

4.	Install the both boot band.

To control the air in the TJ boot, keep the specified distance between the boot bands when they are tightened.

Engine	TM	Distance(L) mm(in.)
Engine	TM	LH side	RH side
Gamma 1.4 MPI	6 M/T	545.9(214921)	826.2(32.5275)
Gamma 1.6 GDI/MPI	6 M/T	545.9(214921)	826.2(32.5275)
Gamma 1.6 MPI	6 A/T	522.8(20.5826)	814.6(32.0708)
Gamma 1.6 GDI	6 DCT	493.3(19.4212)	878.8(34.5984)
U-II 1.4 TCI	6 M/T	546.1(21.5000)	826.4(32.5354)
U-II 1.6 TCI	6 M/T	540.1(21.2637)	832.4(32.7716)
U-II 1.6 TCI	6 A/T	523.0(20.5905)	814.7(32.0747)
Gamma 1.6 TGDI	6 M/T	517.9(20.3897)	530.6(20.8897)
Kappa 1.0 TGDI	6 M/T	572.2(22.5275)	800.5(31.5157)

Using the SST(09495-3K000), secure the TJ boot bands.

Clearance (A): 2.0 mm (0.0787 in.) or less

7.	Install the Front Driveshaft. (Refer to Driveshaft Assembly - “Front Driveshaft”)

TJ Joint Components and components location

Components [LH] 1. BJ assembly 2. BJ circlip 3. BJ boot band 4. BJ boot 5. Shaft 6. TJ boot band 7. TJ boot 8. Sp ...

Dynamic Damper Components and components location

Components 1. BJ assembly 2. BJ circlip 3. BJ boot band 4. BJ boot 5. Dynamic damper band 6. Dynamic damper 7. Shaft 8. TJ boo ...

Other information:

Kia Cee'd JD Service Manual: Front Lower Arm Repair procedures
Replacement 1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2. Remove the front wheel and tire (A) from front hub. Tightening torque: 88.2 ~ ...

Kia Cee'd JD Owners Manual: Owner’s responsibility
✽ NOTICE Maintenance Service and Record Retention are the owner's responsibility. We recommend in general that you have your vehicle serviced by an authorized Kia dealer. You should retain documents that show proper maintenance has been performed on your vehicle in accordance with th ...