Kia Rio: Smart Key System / Smart Key Diagnostic
Repair procedures
Inspection |
Self Diagnosis With Scan Tool
It will be able to diagnose defects of SMART KEY system with KDS/GDS quickly. KDS/GDS can operates actuator forcefully, input/output value monitoring and self diagnosis.
The following three features will be major problem in SMART KEY system.
1. |
Problem in SMART KEY unit input. |
2. |
Problem in SMART KEY unit. |
3. |
Problem in SMART KEY unit output. |
So the following three diagnosis operates will be the major problem solution process.
1. |
SMART KEY unit Input problem : switch diagnosis |
2. |
SMART KEY unit problem : communication diagnosis |
3. |
SMART KEY unit Output problem : antenna and switch output diagnosis |
Switch Diagnosis
1. |
Connect the cable of KDS/GDS to the data link connector in driver side crash pad lower panel, turn the power on KDS/GDS. |
2. |
Select the vehicle model and then SMART KEY system. |
3. |
Select the "SMART KEY unit". |
4. |
After IG ON, select the "Current data".
|
5. |
You can see the situation of each switch on scanner after connecting the "current data" process.
|
Communication Diagnosis With KDS/GDS (Self Diagnosis)
1. |
Communication diagnosis checks that the each linked components operates normal. |
2. |
Connect the cable of KDS/GDS to the data link connector in driver side crash pad lower panel. |
3. |
After IG ON, select the "DTC".
|
Antenna Actuation Diagnosis
1. |
Connect the cable of KDS/GDS to the data link connector in driver side crash pad lower panel. |
2. |
After IG ON, select the "Actation Test".
|
3. |
Set the smart key near the related antenna and operate it with a KDS/GDS. |
4. |
If the LED of smart key is blinking, the smart key is normal. |
5. |
If the LED of smart key is not blinking, check the voltage of smart key battery. |
6. |
Antenna actuation
|
Antenna Status Check
1. |
Connect the cable of KDS/GDS to the data link connector in driver side crash pad lower panel. |
2. |
Select the "Antenna Status Check".
|
3. |
After IG ON, select the "Antenna Status Check".
|
4. |
Set the smart key near the related antenna and operate it with a KDS/GDS.
|
5. |
If the smart key runs normal , the related antenna, smart key(transmission, reception) and exterior receiver are normal. |
6. |
Antenna status
|
FOB Status Check
1. |
Connect the cable of KDS/GDS to the data link connector in driver side crash pad lower panel. |
2. |
After IG ON, select the "FOB KEY STATUS INFO".
|
Smart Key Status Check
1. |
Connect the cable of KDS/GDS to the data link connector in driver side crash pad lower panel. |
2. |
After IG ON, select the "SMK STATUS INFO".
|
Neutralization Status Check
1. |
Connect the cable of KDS/GDS to the data link connector in driver side crash pad lower panel. |
2. |
After IG ON, select the "Neutralization mode".
|
Smart Key Unit
Components and components location Components Connector Pin Information No. Connector A Connector B Connector C 1 ...Sunroof
Components and components location Component Location 1. Sunroof 2. Sunroof switch 3. Sunroof motor & controller Schematic diagrams C ...Other information:
Kia Rio 2017-2020 YB Owners Manual: Defroster
CAUTION - Conductors To prevent damage to the conductors bonded to the inside surface of the rear window, never use sharp instruments or window cleaners containing abrasives to clean the window. If you want to defrost and defog the front windshield, refer to “Windshield Defrosting and Defo ...
Kia Rio 2017-2020 YB Service Manual: Front Washer Motor
Repair procedures Inspection Front Washer Motor 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water. • ...