Kia Rio: Front Seat Belt Replacement
Front Seat Belt Replacement
| •
When installing the belt, make sure not to damaged the
pretensioner.
|
|
1. |
Remove the following items first :
|
| A.
Front seat assembly
(Refer to the BD group - "Front Seat")
|
| B.
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
|
2. |
Disconnect the battery negative cable, and wait for at least three
minutes before beginning work.
|
|
3. |
The seat belt anchor pretensioner (A) can be removed after pushing
the lock pin (B) as arrow direction.
|
|
4. |
Using a screwdriver or remover, remove the center pillar lower
trim (A).
|
|
5. |
Using a screwdriver or remover, remove the center pillar upper
trim (A).
|
|
6. |
After loosening the mounting bolt, then remove the front seat
belt upper anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
7. |
After disconnecting the pretensioner connector lock pin, remove
the seat belt pretensioner connector (A), loosen the mounting bolt,
then remove the pretensioner (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
8. |
Installation is the reverse of removal.
|
|
•
Make sure the connector is plugged in properly.
|
|
•
Replace any damage clips.
|
Height Adjust Replacement
|
1. |
Remove the following items first :
|
| A.
Front seat assembly
(Refer to the BD group – “Front Seat”)
|
| B.
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
| C.
Front seat belt lower anchor
|
| D.
Center pillar lower trim
(Refer to the BD group - "Interior Trim")
|
| E.
Center pillar upper trim
(Refer to the BD group - "Interior Trim")
|
| F.
Front seat belt upper anchor
|
|
2. |
After loosening the bolts, then remove the height adjustor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
3. |
Installation is the reverse of removal.
|
|
•
Replace ant damaged clips.
|
|
•
Make sure the height adjust properly.
|
Front Seat Belt Buckle Replacement
|
1. |
Remove the following items first :
|
| A.
Front seat assembly
(Refer to the BD group - "Front Seat")
|
|
2. |
Remove the front seat belt buckle connector mounting clip (A).
|
|
3. |
After loosening the mounting bolt, then remove the front seat
belt buckle (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
4. |
Installation is the reverse of removal.
|
[Front]
(5 Door, 4 Door)
1. Front seat belt
2. Height adjust
3. Front seat belt anchor pretensioner (NA : North america)
[Rear]
...
Rear Seat Belt Replacement
[5 Door]
•
When installing the belt, make sure not ...
See also:
Cruise control system
The cruise control system allows you to program the vehicle to maintain a constant
speed without depressing the accelerator pedal.
This system is designed to function above approximately 25 mph (40 ...
Removal
1.
Turn the ignition switch OFF and disconnect the battery negative
(-) cable.
2.
Disconnect the connector (A), and then remove the sensor ...
Transmitter Inspection
1.
Check that the red light flickers when the door lock or unlock
button is pressed on the transmitter.
2.
Remove the battery and check vol ...
Components
Rear Seat Belt Replacement