Kia Rio: Rear Seat Replacement
Rear Seat Assembly Replacement
|
1. |
After loosening the mounting bolt, then remove the rear seat cushion
(A).
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
|
|
|
2. |
Disconnect the rear seat buckle connector (B).
|
|
3. |
After loosening the mounting bolt, then remove the center rear
seat belt lower anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)
|
|
|
4. |
After loosening the mounting bolts, then remove the rear seat
back (A).
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
|
|
|
5. |
Installation is the reverse of removal.
|
Rear Seat Back Cover Replacement [LH]
| [5 Door] |
| •
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts your hands.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Remove the following items first :
|
| A.
Rear seat back assembly [LH]
|
|
2. |
Push the lock pin (B), remove the headrest (A).
|
|
3. |
Remove the rear latch knob (A) after turning in the counter clock-wise
direction.
|
|
4. |
Remove the rear back knob bush (B).
|
|
5. |
Using a screwdriver or remover, remove the webbing guide (A).
|
|
6. |
After loosening the mounting screw, then remove the rear seat
back latch cover (A).
|
|
7. |
Remove the rear seat back lower mounting protector (A).
|
|
8. |
Zip off the rear seat back cover (A), and then full it up.
|
|
9. |
Pull out the headrest guides (A) while pinching the end of the
guides, and remove them.
|
|
10. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
|
11. |
After removing the hog-ring clips (B) on the rear of seat back
and remove the rear seat back cover (A).
|
|
12. |
Installation is the reverse of removal.
|
|
•
To prevent wrinkles, make sure the material is
stretched evenly over the cover (B) before securing
the hog-ring clips (A).
|
|
•
Replace the hog ring clips with new ones using
special tool [C (09880-4F000)].
|
| [4 Door] |
| •
Put on gloves to protect your hands.
|
| •
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts your hands.
|
|
1. |
Remove the rear seat back assembly [LH].
|
|
2. |
Push the lock pin (B), remove the headrest (A).
|
|
3. |
After loosening the mounting screw, then remove the rear seat
back webbing guide (A).
|
|
4. |
Remove the rear latch knob (A) after turning in the counter clock-wise
direction.
|
|
5. |
Remove the rear seat back lower mounting protector (A).
|
|
6. |
Zip off the rear seat back cover (A), and then full it up.
|
|
7. |
Remove the hog-ring clips (A).
|
|
8. |
Pull out the headrest guides (A) while pinching the end of the
guides, and remove them.
|
|
9. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
|
10. |
After removing the hog-ring clips (B) on the rear of seat back
and remove the rear seat back cover (A).
|
|
11. |
Installation is the reverse of removal.
|
|
•
To prevent wrinkles, make sure the material is
stretched evenly over the cover (B) before securing
the hog-ring clips (A).
|
|
•
Replace the hog ring clips with new ones using
special tool [C (09880-4F000)].
|
Rear Seat Latch Replacement [LH]
| •
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts your hands.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Remove the following items first :
|
| A.
Rear seat back assembly [LH]
|
| B.
Rear seat back cover [LH]
|
|
2. |
After loosening the mounting bolts, then remove the rear seat
latch assembly (A).
[5 Door]
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
|
[4 Door]
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
|
|
|
3. |
Installation is the reverse of removal.
|
Rear Seat Back Cover Replacement [RH]
| [5 Door] |
| •
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts your hands.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Remove the following items first :
|
| A.
Rear seat back assembly [RH]
|
|
2. |
Push the lock pin (B), remove the headrest (A).
|
|
3. |
Remove the rear latch knob (A) after turning in the counter clock-wise
direction.
|
|
4. |
Remove the rear back knob bush (B).
|
|
5. |
After loosening the mounting screw, then remove the rear seat
back latch cover (A).
|
|
6. |
Remove the rear seat back lower mounting protector (A).
|
|
7. |
Zip off the rear seat back cover (A), and then full it up.
|
|
8. |
Pull out the headrest guides (A) while pinching the end of the
guides, and remove them.
|
|
9. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
|
10. |
After removing the hog-ring clips (B) on the rear of seat back
and remove the rear seat back cover (A).
|
|
11. |
Installation is the reverse of removal.
|
|
•
To prevent wrinkles, make sure the material is
stretched evenly over the cover (B) before securing
the hog-ring clips (A).
|
|
•
Replace the hog ring clips with new ones using
special tool [C (09880-4F000)].
|
| [4 Door] |
| •
Put on gloves to protect your hands.
|
| •
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts your hands.
|
|
1. |
Remove the rear seat back assembly [RH].
|
|
2. |
Push the lock pin (B), remove the headrest (A).
|
|
3. |
After loosening the mounting screw, then remove the rear seat
back webbing guide (A).
|
|
4. |
Remove the rear latch knob (A) after turning in the counter clock-wise
direction.
|
|
5. |
Remove the rear seat back lower mounting protector (A).
|
|
6. |
Zip off the rear seat back cover (A), and then full it up.
|
|
7. |
Remove the hog-ring clips (A).
|
|
8. |
Pull out the headrest guides (A) while pinching the end of the
guides, and remove them.
|
|
9. |
Remove the rear seat back cover (A) from the rear seat back frame
(B).
|
|
10. |
After removing the hog-ring clips (B) on the rear of seat back
and remove the rear seat back cover (A).
|
|
11. |
Installation is the reverse of removal.
|
|
•
To prevent wrinkles, make sure the material is
stretched evenly over the cover (B) before securing
the hog-ring clips (A).
|
|
•
Replace the hog ring clips with new ones using
special tool [C (09880-4F000)].
|
Rear Seat Latch Replacement [RH]
| •
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts your hands.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Remove the following items first :
|
| A.
Rear seat back assembly [RH]
|
| B.
Rear seat back cover [RH]
|
|
2. |
After loosening the mounting bolts, then remove the rear seat
latch assembly (A).
[5 Door]
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)
|
[4 Door]
|
|
3. |
Installation is the reverse of removal.
|
Rear Seat Cushion Cover Replacement
| •
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts your hands.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Remove the following items first :
|
| A.
Rear seat cushion cover assembly
|
|
2. |
Remove the hog-ring clips (A).
|
|
3. |
After removing the hog-ring clips (B) on the rear of seat cushion
and remove the rear seat cushion cover (A).
|
|
4. |
Installation is the reverse of removal.
|
|
•
To prevent wrinkles, make sure the material is
stretched evenly over the cover (B) before securing
the hog-ring clips (A).
|
|
•
Replace the hog ring clips with new ones using
special tool [C (09880-4F000)].
|
[5 Door]
1. Headrest
2 . Headrest guide
3 . Webbing guide
4 . Rear latch knob
5 . Rear back knob bush
6 . Rear seat back silencer cloth
7 . Rear seat back pad ...
See also:
Intake Actuator Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the intake actuator connector.
3.
Verify that the intake actuato ...
Smart key unit Inspection
Smart Key Unit
-
Refer to the BE group - inspection / self diagnosis with GDS.
Smart Key Switch
-
Refer to the BE group - inspection / self di ...
Curtain Airbag (CAB) Module Description
Curtain airbags are installed inside the headliner (LH and RH) and protect
the driver and passenger from danger when side crash occurs. The SRSCM determines
deployment of curtain airbag by us ...
Rear Seat Components
Seat Belt