Kia Rio: Roof Trim Replacement
Sunvisor Replacement
| •
Use a plastic panel removal tool to remove interior trip
pieces to without marring the surface.
|
| •
Put on gloves to protect your hands.
|
|
1. |
After loosening the mounting screws, then remove the sunvisor
(A) and retainer (B).
|
|
2. |
Installation is the reverse of removal.
|
Assist Handle Replacement
| •
Use a plastic panel removal tool to remove interior trip
pieces to without marring the surface.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Remove the covers (B).
|
|
2. |
After loosening the mounting bolts, then remove the assist handle
(A).
|
|
3. |
Installation is the reverse of removal.
|
Overhead Console Replacement
| •
Use a plastic panel removal tool to remove interior trip
pieces to without marring the surface.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Using a screwdriver or remover, remove the overhead console cover
(A).
|
|
2. |
After loosening the mounting screws, then remove the overhead
console assembly (A).
|
|
3. |
Disconnect the connectors (A).
|
|
4. |
Installation is the reverse of removal.
|
|
•
Make sure the connector is connected properly.
|
Room Lamp Replacement
| •
Use a plastic panel removal tool to remove interior trip
pieces to without marring the surface.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Using a screwdriver or remover, remove the room lamp cover (B).
|
|
2. |
After loosening the mounting screws, then remove the room lamp
(A).
|
|
3. |
Disconnect the connector (A).
|
|
4. |
Installation is the reverse of removal.
|
|
•
Make sure the connectors are connected in properly.
|
|
•
Replace any damage clips.
|
Vanity Lamp Replacement
| •
Use a plastic panel removal tool to remove interior trip
pieces to without marring the surface.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Using a screwdriver or remover, remove the vanity lamp (A).
|
|
2. |
Disconnect the connector (B).
|
|
3. |
Installation is the reverse of removal.
|
|
•
Make sure the connectors are connected in properly.
|
|
•
Replace any damage clips.
|
Roof Trim Replacement
| •
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts, to prevent damage.
|
| •
Put on gloves to protect your hands.
|
|
1. |
Remove the following items :
|
| A.
Front seat
(Refer to the BD group - "Front Seat")
|
| B.
Rear seat
(Refer to the BD group - "Rear Seat")
|
| C.
Sunvisor
|
| D.
Overhead console
|
| E.
Room lamp
|
| F.
Sunglass case
|
| G.
Assist handle
|
| H.
Front pillar trim
(Refer to the BD group - " Interior Trim")
|
| I.
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - " Interior Trim")
|
| J.
Center pillar lower trim & Center pillar upper trim
(Refer to the BD group - " Interior Trim")
|
| K.
Luggage side trim [5 Door]
(Refer to the BD group - " Interior Trim")
|
| L.
Rear pillar trim
(Refer to the BD group - " Interior Trim")
|
|
2. |
Disconnect the roof trim main connector (A).
|
|
3. |
Disconnect the sunroof motor connector (A).
|
|
4. |
Remove the clips and roof trim (A).
|
|
5. |
Installation is the reverse of removal.
|
|
•
Make sure the connectors are plugged in properly.
|
|
•
Replace any damage clips.
|
Components
[General Type]
1 . Roof trim
2 . Sunvisor
3 . Retainer
4 . Assist handle bracket assembly
[Sunroof Type]
1 . Roof t ...
[5 Door, 4 Door]
1 . Front pillar trim
2 . Center pillar upper trim
3 . Center pillar lower trim
4 . Rear pillar trim [5 Door]
5 . Front door scuff trim
6 . ...
See also:
ECM Terminal And Input/Output signal [A/T]
ECM Terminal Function (A/T)
Connector [EGGA-AG]
Pin No.
Description
Connected to
1
Injector (Cylinder #1) [High] control output
...
Measuring Body Dimensions
1.
Basically, all measurements in this manual are taken with a tracking
gauge.
2.
When a measuring tape is used, check to be sure there is ...
Multimedia Jack Removal
1.
Using a screwdriver or remover, remove the multimidia jack assembly.
...
Roof Trim
Interior Trim Components