Kia Ceed Manuals Ceed Car Manuals
Technical Info

Kia Cee'd: Tires/Wheels / Alignment Repair procedures

Front wheel alignment
  
When using a commercially available computerized wheel alignment equipment to inspect the front wheel alignment, always position the vehicle on a level surface with the front wheels facing straight ahead.
Prior to inspection, make sure that the front suspension and steering system are in normal operating condition and that the tires are inflated to the specified pressure.
Toe

B - A > 0: Toe in (+)
B - A < 0: Toe out (-)
Toe adjustment
1.
Loosen the tie rod end lock nut.
2.
Remove the bellows clip to prevent the bellows from being twisted.
3.
Adjust the toe by screwing or unscrewing the tie rod. Toe adjustment should be made by turning the right and left tie rods by the same amount.
Toe-in
Total : 0.16° ± 0.2°
Individual : 0.08° ± 0.1°

4.
When completing the toe adjustment, install the bellows clip and tighten the tie rod end lock nut to specified torque.
Tightening torque:
49.0 ~ 53.9 N.m (5.0 ~ 5.5 kgf.m, 36.2 ~ 39.8 lb-ft)
Camber and Caster
Camber and Caster are pre-set at the factory, so they do not need to be adjusted. If the camber and caster are not within the standard value, replace or repair the damaged parts and then inspect again.
Camber angle : -0.5° ± 0.5°
Caster angle : 5.2° ± 0.5°
Rear wheel alignment
  
When using a commercially available computerized wheel alignment equipment to inspect the rear wheel alignment, always position the vehicle on a level surface.
Prior to inspection, make sure that the rear suspension system is in normal operating condition and that the tires are inflated to the specified pressure.
Toe

B - A > 0: Toe in (+)
B - A < 0: Toe out (-)
Toe adjustment
1.
Loosen the nut holding the assist arm cam bolt (A).
2.
Adjust rear toe by turning the rear assist arm cam bolt (A) clockwise or counter clockwise. Toe adjustment should be made by turning the right and left cam bolt by the same amount.
Toe-in
Total : 0.14° ± 0.2°
0.06° ± 0.2° (Only "T-GDI")
Individual : 0.07° ± 0.1°
0.03° ± 0.1° (Only "T-GDI")

3.
When completing the toe adjustment, tighten the nut to specified torque.
Tightening torque:
98.1 ~ 117.7Nm (10.0 ~ 12.0kgf.m, 72.3 ~ 86.8lb-ft)
Camber
Camber is pre-set at the factory, so it does not need to be adjusted. If the camber is not within the standard value, replace or repair the damaged parts and then inspect again.
Camber : -1.0° ± 0.5°
Wheel Repair procedures
Hub nut tightening sequence Tighten the hub nuts as follows. Tightening torque: 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft) ...
Tire Pressure Monitoring System
...
Other information:

Kia Cee'd JD Owners Manual: For 15, 16 inch tire
For safe operation, carefully read and follow the instructions in this manual before use. (1) Compressor (2) Sealant bottle The Tire Mobility Kit is a temporary fix to the tire and we recommend that the system be inspected by an authorized Kia dealer. CAUTION When two or more tires ...

Kia Cee'd JD Service Manual: Movable Glass Repair procedures
Replacement 1. Open the movable glass fully. 2. Loosen the movable glass mounting screws (A).    • ...

Copyright © www.kiamanual.com 2020-2024 | Privacy Policy | Kia Car Parts