Kia Cee'd: Rear Seat / Rear Seat Back Cover Repair procedures

Kia Cee'd JD Service Manual / Body (Interior and Exterior) / Rear Seat / Rear Seat Back Cover Repair procedures

Replacement

[LH]

•	Put on gloves to protect your hands.

•	Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.

•	Take care not to bend or scratch the trim and panels.

1.	Remove the rear seat back assembly [LH]. (Refer to Rear Seat - "Rear Seat Assembly")

2.	Push the lock pin (B), remove the rear seat headrest (A).

3.	Using a screwdriver or remover, remove the rear seat latch cover (A).

4.	Using a screwdriver or remover, remove the rear seat pivot bush (A).

5.	Disconnect the rear seat back cover protector (A).

6.	Pull out the headrest guides (A) while pinching the end of the guides, and remove them.

7.	Remove the rear seat back cover (A) from the rear seat back structure (B).

8.	After removing the hog-ring clips (A) on the rear of seat back and remove the rear seat back cover (B).

Install in the reverse order of removal.

•	To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).

•	Replace the hog-ring clips with new ones using special tool [C (09880-4F000)].

[RH]

•	Put on gloves to protect your hands.

•	Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.

•	Take care not to bend or scratch the trim and panels.

1.	Remove the rear seat back assembly [RH]. (Refer to Rear Seat - "Rear Seat Assembly")

2.	Push the lock pin (B), remove the rear seat headrest (A).

3.	Using a screwdriver or remover, remove the rear seat latch cover (A).

4.	Using a screwdriver or remover, remove the rear seat belt outlet cover (A).

5.	Using a screwdriver or remover, remove the rear seat pivot bush (A).

To remove the rear seat armrest

[5Door, Waggon only]

(1)	Press the lock pin (A) and then push the rear seat armrest mounting bracket (B) in the direction of the arrow in the below picture. [LH]

(2)	First, remove the lock washer (A). [RH]

(3)	Press the lock pin (A) and then push the rear seat armrest mounting bracket (B) in the direction of the arrow in the below picture. [RH]

7.	Remove the rear seat armrest (A) by lifting the left side. [5Door, Waggon only]

8.	Disconnect the rear seat back cover protector (A).

9.	Disconnect the rear seat back upper protector (A).

10.	Pull out the headrest guides (A) while pinching the end of the guides, and remove them.

11.	Remove the rear seat back cover (A) from the rear seat back structure (B).

12.	After removing the hog-ring clips (A) on the rear of seat back and remove the rear seat back cover (B).

13.

Install in the reverse order of removal.

•	To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).

•	Replace the hog-ring clips with new ones using special tool [C (09880-4F000)].

Rear Seat Back Cover Components and components location

Component Location 1. Rear seat back cover [LH] 2. Rear seat back cover [RH] ...

Rear Seat Cushion Cover Components and components location

Component Location 1. Rear seat cushion cover [LH] 2. Rear seat cushion cover [RH] ...

Other information:

Kia Cee'd JD Service Manual: Cluster Fascia Panel Components and components location
Component Location 1. Cluster fascia panel ...

Kia Cee'd JD Service Manual: Clutch Actuator Motor 1 (Odd Gear) Repair procedures
Inspection 1. Turn off the ignition switch. 2. Disconnect the clutch motor connector (A). 3. Measure the resistance on the clutch motor terminal. 4. Refer to the spec ...