Kia Rio: Front Suspension System / Front Strut Assembly

Kia Rio 2017-2020 YB Service Manual / Suspension System / Front Suspension System / Front Strut Assembly

Components and components location

Components Location

1. Lock nut
2. Insulator dust cap
3. Self lock nut
4. Strut insulator
5. Strut bearing
6. Spring upper seat

7. Spring upper pad
8. Coli spring
9. Dust cover
10. Bumper rubber
11. Spring lower pad
12. Shock absorber

Repair procedures

Removal

Remove wheel nuts, front wheel and tire from front hub.

Tightening torque:

107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Be careful not to damage the hub bolts when removing the front wheel and tire.

2.	Remove the cowl top cover. (Refer to Body - "Cowl Top Cover")

Remove the strut lock nuts (A).

Tightening torque:

49.0 - 58.8 N·m (5.0 - 6.0 kgf·m, 36.2 - 43.4 lb·ft)

Remove the brake caliper hose bracket bolt (A) and wheel speed sensor bracket bolt (B).

Tightening torque:

A : 8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)

B : 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Remove the stabilizer link nut (A).

Tightening torque:

98.0 - 117.6 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.7 lb·ft)

•	When loosening the nut (A), fix the outer hexagon of stabilizer bar link.

•	Be careful not to damage the stabilizer link boots.

Loosen the bolts and then remove the strut assembly (A) from the knuckle.

Tightening torque:

98.0 - 117.6 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.7 lb·ft)

7.	Install in the reverse order of removal.

Disassembly

Using a strut spring compressor, compress the coil spring.

•	To prevent peeling the paint of coil spring, cover the coil spring with a thin cloth or hose before installing strut spring compressor.

•	Set the compression position of strut spring compressor correctly for coil spring not to slant when compressing the coil spring.

Using the SST (09546-3X100), loosen the self locking nut.

Tightening torque:

68.6 - 78.5 N·m (7.0 - 8.0 kgf·m, 50.6 - 57.9 lb·ft)

3.	Remove the insulator, spring seat, coil spring and dust cover from the strut assembly.

4.	Reassembly is the reverse of the disassembly.

Inspection

1.	Check the strut insulator for wear or damage.

2.	Check rubber parts for damage or deterioration.

3.	Compress and extend the piston rod (A) and check that there is no abnormal resistance or unusual sound during operation.

Disposal

1.	Fully extend the piston rod.

2.	Drill a hole on the A section to remove gas from the cylinder.

Front Suspension System

Components and components location Components Location 1. Gear box 2. Stabilizer bar 3. Driveshaft 4. Stabilizer link 5. Shock absorber 6. Front axle ...

Front Lower Arm

Repair procedures Removal 1. Remove wheel nuts, front wheel and tire from front hub. Tightening torque: 107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79 ...

Other information:

Kia Rio 2017-2020 YB Service Manual: Front Door Trim

Components and components location Component Location 1. Front door trim Repair procedures Replacement Put on gloves to protect your hands. ...

Kia Rio 2017-2020 YB Owners Manual: Stop and tail lamp / Side marker (Bulb type) replacement (for 4 door)

1. Open the trunk lid. 2. Remove the service cover by pulling out the service cover. 3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly. 4. Remove the bulb from the socket by pressing it in and rota ...