Kia Rio: Body Electrical System / Multifunction Switch

Kia Rio 2017-2020 YB Service Manual / Body Electrical System / Multifunction Switch

Specifications

Items		Specifications
Rated voltage		DC 12 V
Operating temperature range		-22 - 176°F (-30 - 80°C)
Rated load	Washer	Washer : 6A (Motor load)

Components and components location

Components

[BCM Type]

1 . Steering column shaft
2 . Lighting switch
3 . Wiper/Washer switch

4 . Screws
5 . Clock spring

[Non -BCM Type]

1 . Steering column shaft
2 . Lighting switch
3 . Wiper/Washer switch

4 . Screws
5 . Clock spring

[BCM Type]

(LHD)

(RHD)

[Non -BCM Type]

(LHD)

(Turn Signal Lamp Switch / Dimmer & Passing Switch)

(Wiper Switch / Washer Switch)

(RHD)

(Wiper Switch / Washer Switch)

(Turn Signal Lamp Switch / Dimmer & Passing Switch)

Repair procedures

Removal

[BCM Type]

1.	Disconnect the negative (-) battery terminal.

2.	Remove the steering wheel. (Refer to Steering System - "Steering Wheel")

3.	Remove the steering column upper and lower shrouds after loosening the screws. (Refer to Body - "Steering Column Shroud Panal")

4.	Remove the clock spring. (Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")

5.	Disconnect the multifunction switch connector (A).

6.	Remove the multifunction switch assembly (A) after loosening the screws.

[Non -BCM Type]

(LH)

(Turn Signal Lamp Switch / Dimmer & Passing Switch)

1.	Disconnect the negative (-) battery terminal.

2.	Remove the steering column upper and lower shrouds after loosening the screws. (Refer to Body - "Steering Column Shroud Panal")

3.	Remove the wiper switch / washer switch. (Refer to Body Electrical System - "Multifunction Switch")

4.	Remove the steering wheel. (Refer to Steering System - "Steering Wheel")

5.	Remove the clock spring. (Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")

6.	Disconnect the turn signal lamp switch / dimmer & passing switch connector (A).

7.	Remove the turn signal lamp switch / dimmer & passing switch (A) after loosening the mounting screws.

(RH)

(Wiper Switch / Washer Switch)

1.	Disconnect the negative (-) battery terminal.

2.	Remove the steering column upper and lower shrouds after loosening the screws. (Refer to Body - "Steering Column Shroud Panal")

3.	Disconnect the wiper switch / washer switch connector (A).

4.	Remove the wiper switch / washer switch (A) by pushing the lock pin (B).

Installation

[BCM Type]

1.	Install the multifunction switch.

2.	Install the clock spring.

3.	Install the steering column upper and lower shrouds.

4.	Install the steering wheel.

5.	Connect the negative (-) battery terminal.

[Non-BCM Type]

(LH)

(Turn Signal Lamp Switch / Dimmer & Passing Switch)

1.	Install the turn signal lamp switch / dimmer & passing switch.

2.	Connect the turn signal lamp switch / dimmer & passing switch connector.

3.	Install the clock spring.

4.	Install the steering wheel.

5.	Install the wiper switch / washer switch.

6.	Install the steering column upper and lower shrouds.

7.	Connect the negative (-) battery terminal.

(RH)

(Wiper Switch / Washer Switch)

1.	Install the wiper switch / washer switch.

2.	Connect the wiper switch / washer switch connector.

3.	Install the steering column upper and lower shrouds.

4.	Connect the negative (-) battery terminal.

Inspection

Multifunction Switch Inspection

[BCM Type]

Check for continuity between the terminals in each switch position as shown below.

[Left Handle Drive]

Switch	Switch position	Switch terminal	Resistance (Ω, ±3.5%)
Front wiper switch	MIST	1-9	330
	OFF		∞
	Intermittent (AUTO)		800
	LOW		1,800
	HIGH		5,700
Rear wiper switch	OFF	9-16	∞
	LOW		910
	HIGH		2,910
Wiper intermittent volume	Volume 1	7-9	330
	Volume 2		690
	Volume 3		1,310
	Volume 4		2,610
	Volume 5		7,310
Fog lamp switch	OFF	9-10	∞
	Front fog lamp		910
	Rear fog lamp		2,910
Turn signal switch	OFF	9-12	∞
	Left		910
	Right		2,910
Dimmer & Passing switch	OFF	9-13	∞
	Passing		910
	Dimmer		2,910
Light switgh	OFF	9-14	∞
	AUTO		680
	Tail lamp		1,680
	Low beam		5,580

[Right Handle Drive]

Switch	Switch position	Switch terminal	Resistance (Ω, ±3.5%)
Front Wiper switch	MIST	3-16	330
	OFF		∞
	Intermittent (AUTO)		800
	LOW		1,800
	HIGH		5,700
Rear wiper switch	OFF	9-16	∞
	LOW		910
	HIGH		2,910
Wiper intermittent volume	Volume 1	2-16	330
	Volume 2		690
	Volume 3		1,310
	Volume 4		2,610
	Volume 5		7,310
Fog lamp switch	OFF	14-16	∞
	Front fog lamp		910
	Rear fog lamp		2,910
Turn signal switch	OFF	13-16	∞
	Left		910
	Right		2,910
Dimmer & Passing switch	OFF	12-16	∞
	Passing		910
	Dimmer		2,910
Light switgh	OFF	11-16	∞
	AUTO		680
	Tail lamp		1,680
	Low beam		5,580

[Non -BCM Type]

(LH)

(Turn Signal Lamp Switch / Dimmer & Passing Switch)

1.	Check for continuity between the terminals in each switch position as shown below. Lighting switch (Auto light) [LHD] [RHD] Lighting Switch (Standard) [LHD] [RHD] Dimmer And Passing Switch [LHD] [RHD] Turn Signal Switch [LHD] [RHD] Front/Rear Fog Lamp [LHD] [RHD]

(RH)

(Wiper Switch / Washer Switch)

1.	Check for continuity between the terminals in each switch position as shown below. Front Wiper & Washer Switch [LHD] [RHD] Front Washer Switch [LHD] [RHD] Rear Wiper & Washer Switch [LHD] [RHD]

Inspection (With KDS/GDS)

[BCM Type Only]

In the body electrical system, failure can be quickly diagnosed by using the vehicle diagnostic system (KDS/GDS).

The diagnostic system(KDS/GDS) provides the following information.

(1)	Self diagnosis : Checking failure and code number (DTC)

(2)	Current data : Checking the system input/output data state

(3)	Actuation test : Checking the system operation condition

(4)	Additional function : Controlling other features including system option setting and zero point adjustment

2.	Select the 'Car model' and the 'Body Control Module (BCM)' to be checked in order to check the vehicle with the tester.

3.	Select the 'Current Data' menu to search the current state of the input/output data.

Rear Combination Lamp

Repair procedures Removal Rear Combination Lamp (Outside) 1. Disconnect the negative (-) battery terminal. 2. Remove the rear combination lamp ...

Power Door Locks

Components and components location Component Location 1. Driver power window switch 2. Assist power window switch 3 . Body Comtrol Module (BCM) 4 . Tailgate a ...

Other information:

Kia Rio 2017-2020 YB Service Manual: Rear Door Trim

Components and components location Component Location 1. Rear door trim Repair procedures Replacement Put on gloves to protect your hands. ...

Kia Rio 2017-2020 YB Owners Manual: Blade replacement

When the wipers no longer clean adequately, the blades may be worn or cracked, and require replacement. To prevent damage to the wiper arms or other components, do not attempt to move the wipers manually. Aftermarket wiper blades may result in wiper malfunction and/or failure. It is recommen ...