Kia Rio Manuals Rio Car Manuals
Technical Info

Kia Rio: Power Door Locks / Power Door Lock Module

Kia Rio 2017-2020 YB Service Manual / Body Electrical System / Power Door Locks / Power Door Lock Module
Components and components location
Components

1. Door lock/unlock knob cable
2. Door latch assembly

Repair procedures
Inspection
  

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Be careful to store and handle the trim when removing/installing because lubricant and oil can leave a stain on the trim.

Front Door Lock Module Inspection

1.

Remove the front door trim.

(Refer to Body - "Front Door Trim")

2.

Remove the front door trim seal.

(Refer to Body - "Front Door Window Glass")

3.

Disconnect the connector from the actuator.

[Central Lock Motor]

No.
Pin Information
LH
RH
1
-
-
2
Motor 2
COM
3
Motor 3
Lock / Unlock switch
4
Key unlock switch
Key lock switch
5
Key lock switch
Key unlock switch
6
Lock / Unlock switch
Motor 3
7
COM
Motor 2
8
-
-

[Dead Lock Motor]

No.
Pin Information
LH
RH
1
Motor 1
-
2
Motor 2
COM
3
Motor 3
Lock / Unlock switch
4
Key unlock switch
Key lock switch
5
Key lock switch
Key unlock switch
6
Lock / Unlock switch
Motor 3
7
COM
Motor 2
8
-
Motor 1

4.

Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily.

[Central Lock Motor]

[Dead Lock Motor]

[Central Lock Motor]

(LH)

(RH)

[Dead Lock Motor]

Rear Door Lock Module Inspection

1.

Remove the rear door trim.

(Refer to Body - "Rear Door Trim")

2.

Remove the rear door trim seal.

(Refer to Body - "Rear Door Window Glass")

3.

Disconnect the connector from the actuator.

[Central Lock Motor]

No.
Pin Information
LH
RH
1
-
-
2
Motor 2
COM
3
Motor 3
Lock / Unlock switch
4
-
-
5
-
-
6
Lock / Unlock switch
Motor 3
7
COM
Motor 2
8
-
-

[Dead Lock Motor]

No.
Pin Information
LH
RH
1
Motor 1
-
2
Motor 2
COM
3
Motor 3
Lock / Unlock switch
4
-
-
5
-
-
6
Lock / Unlock switch
Motor 3
7
COM
Motor 2
8
-
Motor 1

4.

Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily.

[Central Lock Motor]

[Dead Lock Motor]

[Central Lock Motor]

(LH)

(RH)

[Dead Lock Motor]

Tailgate Lock Module Inspection

1.

Remove the tailgate trim.

(Refer to Body - "Tailgate Trim")

2.

Disconnect the connectors from the actuator.

3.

Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily.

4.

Checking the tailgate of the vehicle power option power refers to the tailgate module.

Power Door Locks
Components and components location Component Location 1. Driver power window switch 2. Assist power window switch 3 . Body Comtrol Module (BCM) 4 . Tailgate a ...
Power Door Lock Switch
Repair procedures Removal    • When removing with a flat-tip screwdriver or remover, wrap prot ...
Other information:

Kia Rio 2017-2020 YB Service Manual: Rear Door Belt Inside Weatherstrip


Repair procedures Replacement 1. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim") 2. Remove the rear door belt outside weatherstrip (A) after loosening the mounting screw. 3. Insta ...

Kia Rio 2017-2020 YB Service Manual: Front Door Belt Outside Weatherstrip


Repair procedures Replacement    Put on gloves to protect your hands.    • Use a plastic panel removal tool to remov ...
Copyright © www.kiamanual.com 2020-2021