Kia Rio: Front Door Replacement
Front Door Trim Replacement
| •
Take care not to scratch the door trim and other parts.
|
| •
Put on gloves to protect your hands.
|
|
1. |
After loosening the mounting screw, then remove the front door
inside handle housing (B).
|
|
2. |
After loosening the mounting screws, then remove the front door
trim (A).
|
|
3. |
Disconnect the power window connector (A) and outside mirror folding
switch connector (B).
|
|
4. |
Installation is the reverse of removal.
|
|
•
Make sure of connectors is plugged in properly
and each rod is connected securely.
|
|
•
Make sure the door lock and opens properly.
|
|
•
Replace any damaged clips.
|
Inside Handle Replacement
|
1. |
Remove the following items :
|
| A.
Front door trim
|
|
2. |
After loosening the mounting screw, then remove the front door
inside handle (A).
|
|
3. |
Disconnect the front door inside handle cable (A).
|
|
4. |
Installation is the reverse of removal.
|
|
•
Replace any damaged clips.
|
|
•
Make sure the door lock and opens properly.
|
Glass Replacement
|
1. |
Remove the following items :
|
| A.
Front door trim
|
|
2. |
After loosening the mounting screw, then remove the front door
inside handle (A).
|
|
3. |
Disconnect the front door inside handle cable (A).
|
|
4. |
Disconnect the front door speaker connector (A).
|
|
5. |
After loosening the mounting screws, then remove the front door
trim seal mounting bracket (B).
|
|
6. |
Remove the front door trim seal (A).
|
|
•
Replace any damaged door trim seal.
|
|
7. |
Remove the front door belt inside weatherstrip (A).
|
|
8. |
Carefully move the glass (A) until you can see the bolts, then
loosen them. Separate the glass from the glass run and carefully pull
the glass out through the window slot.
|
|
•
Take care not to drop to glass and scratch the
glass surface.
|
Tightening torque :
7.8 ~ 10.8 N.m (0.8 ~ 1.1 kgf.m, 5.8 ~ 8.0 lb-ft)
|
|
9. |
Installation is the reverse of removal.
|
|
•
Roll the glass up down to see if it move freely
without binding.
|
|
•
Adjust the position of the glass as necessary.
|
Speaker Replacement
|
1. |
Remove the following items :
|
| A.
Front door trim
|
|
2. |
Disconnect the speaker connector (B).
|
|
3. |
After loosening the mounting screws, then remove the front door
speaker (A).
|
|
4. |
Installation is the reverse of removal.
|
|
•
Use sheet metal screws to secure the speaker.
|
|
•
Make sure connectors are connected properly and
each rod is connected securely.
|
|
•
Make sure the door locks/unlocks and opens/closes
properly.
|
|
•
Replace any damaged clips.
|
Door Power Window Regulator Assembly Replacement
|
1. |
Remove the following items :
|
| A.
Front door trim
|
| B.
Front door trim seal
|
| C.
Front door glass
|
|
2. |
Loosen the front door power window regulator mounting nuts.
|
|
3. |
Disconnect the front door power window motor connector (A).
Tightening torque :
3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3 lb-ft)
|
|
|
4. |
Remove the front door power window regulator assembly (A).
|
|
5. |
After loosening the mounting nuts, then remove the front door
power window motor (A).
|
|
6. |
Installation is the reverse of removal.
|
|
•
Grease should be applied to areas where there
is rotational parts and springs.
|
|
•
Roll the glass up and down to see if it move freely
without binding.
|
Outside Handle Replacement
|
1. |
Remove the following items :
|
| A.
Front door trim
|
|
2. |
After loosening the mounting screw, then remove the front door
inside handle (A).
|
|
3. |
Disconnect the front door inside handle cable (A).
|
|
4. |
Disconnect the front door speaker connector (A).
|
|
5. |
After loosening the mounting screws, then remove the front door
trim seal mounting bracket (B).
|
|
6. |
Remove the front door trim seal (A).
|
|
•
Replace any damaged door trim seal.
|
|
7. |
Remove the hole plug (B).
|
|
8. |
After loosening the mounting bolt, then remove the outside handle
cover (A).
Tightening torque :
7.8 ~ 10.8 N.m (0.8 ~ 1.1 kgf.m, 5.8 ~ 8.0 lb-ft)
|
|
|
9. |
Remove the outside handle (A) by sliding it rearward.
|
|
10. |
Disconnect the outside handle connector (A).
|
|
11. |
Installation is the reverse of removal.
|
|
•
Make sure connectors are connected properly and
each rod is connected securely.
|
|
•
Make sure the door locks/unlocks and opens/closes
properly.
|
|
•
Replace any damaged clips.
|
Door Latch Replacement
|
1. |
Remove the following items :
|
| A.
Front door trim
|
| B.
Front door trim seal
|
|
2. |
Disconnect the outside handle rod (A).
|
|
3. |
Loosen the front door latch (A) mounting screws.
Tightening torque :
7.8 ~ 10.8 N.m (0.8 ~ 1.1 kgf.m, 5.8 ~ 8.0 lb-ft)
|
|
|
4. |
Remove the front door latch assembly (A).
|
|
5. |
Disconnect the front door latch connector (A).
|
|
6. |
Installation is the reverse of removal.
|
|
•
Make sure the connector is connected properly.
|
|
•
Make sure the door locks/unlocks and opens/closes
properly.
|
|
•
Replace any damaged clips.
|
Door Side Weatherstrip Replacement
|
1. |
Detach the clips, then remove the front door side weatherstrip(A).
|
|
2. |
Installation is the reverse of removal.
|
|
•
Replace any damaged clips.
|
1 . Front door trim
2 . Front door trim seal
3 . Front door panel
4. Front door belt inside weatherstrip
5 . Front door belt outside weatherstrip
6. Front door window glass ...
Glass Adjustment
•
Check the glass run channel for damage or deterioration,
and repl ...
See also:
Oil Pressure Switch: Inspection
1.
Check the continuity between the terminal and the body with an
ohmmeter. If there is no continuity, replace the oil pressure switch.
2.
...
Installation
1.
Remove the ignition key from the vehicle.
2.
Disconnect the battery negative cable and wait for at least thirty
seconds.
...
Specification
Item
Specification
Coil Resistance (Ω)
1.5 [20°C(68°F)]
...
Front Door Components
Front Door Adjustment