Kia Cee'd: Clutch Cover And Disc / Repair procedures

Kia Cee'd JD Service Manual / Clutch System / Clutch Cover And Disc / Repair procedures

Removal

Remove the transaxle assembly.

G 1.6 MPI (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.4 MPI (Refer to Manual Transaxle System - " Manual Transaxle")

D 1.6 TCI-U2 (Refer to Manual Transaxle System - " Manual Transaxle")

D 1.4 TCI-U2 (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.6 GDI (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.6 T-GDI (Refer to Manual Transaxle System - " Manual Transaxle")

2.	Remove the clutch cover bolts. Be careful not to be bent or twist bolts. Loosen bolts in diagonal directions.

Inspection

1.	Inspect diaphragm spring wear which is in contact with a concentric slave cylinder bearing.

2.	Check the clutch cover and disc surface for wear or cracks.

3.	Check the clutch disc lining for slipping or oil marks.

Measure the depth from a clutch lining surface to a rivet. If the measured value is less than the specification below, replace it.

Standard value

Clutch disc rivet depth (A): 0.3 mm (0.0118 in.)

Installation

If reinstalling used cover, the cover should be installed with its clutch disc as a set.

Apply grease on a disc spline part and transaxle input shaft spline part as required.

Specified grease: CASMOLY L9508

Amount: 0.2 g

Possible problems when not following

•	When not applying: Excessive wear of splines and bad clutch operation can occur.

•	When excessively applying: Grease can be scattered by centrifugal force which can conaminate the clutch disc. This can cause a loss of friction force causing a slip.

The 'T/M SIDE' marked surface should face the transaxle.

Possible problems when the disc is installed in the opposite direction.

•	Transaxle shift error or a strange sound can occur due to clutch separation.

3.	Install the clutch disc and the cover with SST (A: 09411-1P000).

Install the clutch cover bolts. Not to be bent or twisted, Tighten them in diagonal directions.

Tightening torque:

Gasoline : 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

Diesel : 11.8 ~ 14.7 N.m (1.2 ~ 1.5 kgf.m, 8.7 ~ 10.8 lb-ft)

•	Loosely tighten every clutch cover bolts, then torque to specifications in a diagonal direction. This can prevent twisting, vibration of the cover, and the lifting of the pressure plate.

•	Install the all the components with the specified torques. If not, the clutch torque transaxle may have concerns or the mounting bolt can loosen.

Install the transaxle assembly.

G 1.6 MPI (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.4 MPI (Refer to Manual Transaxle System - " Manual Transaxle")

D 1.6 TCI-U2 (Refer to Manual Transaxle System - " Manual Transaxle")

D 1.4 TCI-U2 (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.6 GDI (Refer to Manual Transaxle System - " Manual Transaxle")

G 1.6 T-GDI (Refer to Manual Transaxle System - " Manual Transaxle")

Components and components location

Components 1. Clutch release fork 2. Clutch cover assembly 3. Clutch disk assembly 4. Clutch release bearing ...

Clutch Switch

...

Other information:

Kia Cee'd JD Service Manual: Heated Steering wheel Schematic diagrams
System Circuit Diagram Terminal Function Housing Pin Function Wire color Pad A GND Back B HEATER Yellow ...

Kia Cee'd JD Owners Manual: User Settings
In this mode there are 3 kinds of the submenu. WARNING Do not adjust the User Setting while driving. You may lose your steering control and cause severe personal injury or accidents. 1. Stop the vehicle with the ignition switch in the ON position or engine running. 2. Press the ▲ ...